| Section 1.1.1 | Axisymmetric analysis of bolted pipe flange connections |
| Section 1.1.2 | Elastic-plastic collapse of a thin-walled elbow under in-plane bending and internal pressure |
| Section 1.1.3 | Parametric study of a linear elastic pipeline under in-plane bending |
| Section 1.1.4 | Indentation of an elastomeric foam specimen with a hemispherical punch |
| Section 1.1.5 | Collapse of a concrete slab |
| Section 1.1.6 | Jointed rock slope stability |
| Section 1.1.7 | Notched beam under cyclic loading |
| Section 1.1.8 | Hydrostatic fluid elements: modeling an airspring |
| Section 1.1.9 | Shell-to-solid submodeling and shell-to-solid coupling of a pipe joint |
| Section 1.1.10 | Stress-free element reactivation |
| Section 1.1.11 | Transient loading of a viscoelastic bushing |
| Section 1.1.13 | Damage and failure of a laminated composite plate |
| Section 1.1.14 | Analysis of an automotive boot seal |
| Section 1.1.15 | Pressure penetration analysis of an air duct kiss seal |
| Section 1.1.16 | Self-contact in rubber/foam components: jounce bumper |
| Section 1.1.17 | Self-contact in rubber/foam components: rubber gasket |
| Section 1.1.18 | Submodeling of a stacked sheet metal assembly |
| Section 1.1.19 | Axisymmetric analysis of a threaded connection |
| Section 1.1.20 | Direct cyclic analysis of a cylinder head under cyclic thermal-mechanical loadings |
| Section 1.1.21 | Erosion of material (sand production) from oil bore hole perforation tunnel |
| Section 1.2.1 | Snap-through buckling analysis of circular arches |
| Section 1.2.2 | Laminated composite shells: buckling of a cylindrical panel with a circular hole |
| Section 1.2.3 | Buckling of a column with spot welds |
| Section 1.2.4 | Elastic-plastic K-frame structure |
| Section 1.2.5 | Unstable static problem: reinforced plate under compressive loads |
| Section 1.2.6 | Buckling of an imperfection-sensitive cylindrical shell |
| Section 1.3.1 | Upsetting of a cylindrical billet: quasi-static analysis with mesh-to-mesh solution mapping (ABAQUS/Standard) and adaptive meshing (ABAQUS/Explicit) |
| Section 1.3.2 | Superplastic forming of a rectangular box |
| Section 1.3.3 | Stretching of a thin sheet with a hemispherical punch |
| Section 1.3.4 | Deep drawing of a cylindrical cup |
| Section 1.3.5 | Extrusion of a cylindrical metal bar with frictional heat generation |
| Section 1.3.7 | Axisymmetric forming of a circular cup |
| Section 1.3.16 | Upsetting of a cylindrical billet: coupled temperature-displacement and adiabatic analysis |
| Section 1.3.17 | Unstable static problem: thermal forming of a metal sheet |
| Section 1.4.1 | A plate with a part-through crack: elastic line spring modeling |
| Section 1.4.2 | Conical crack in a block modeled with and without submodeling |
| Section 1.4.3 | Elastic-plastic line spring modeling of a finite length cylinder with a part-through axial flaw |
| Section 1.4.4 | Crack growth in a three-point bend specimen |
| Section 1.4.5 | Analysis of skin-stiffener debonding under tension |
| Section 1.5.1 | Springback of two-dimensional draw bending |
| Section 1.5.2 | Deep drawing of a square box |
| Section 2.1.1 | Nonlinear dynamic analysis of a structure with local inelastic collapse |
| Section 2.1.2 | Detroit Edison pipe whip experiment |
| Section 2.1.6 | Pressurized fuel tank with variable shell thickness |
| Section 2.1.7 | Modeling of an automobile suspension |
| Section 2.1.15 | Seismic analysis of a concrete gravity dam |
| Section 2.2.1 | Analysis of a rotating fan using substructures and cyclic symmetry |
| Section 2.2.2 | Linear analysis of the Indian Point reactor feedwater line |
| Section 2.2.3 | Response spectra of a three-dimensional frame building |
| Section 2.2.4 | Eigenvalue analysis of a structure using the parallel Lanczos eigensolver |
| Section 2.2.5 | Brake squeal analysis |
| Section 2.2.6 | Dynamic analysis of antenna structure utilizing residual modes |
| Section 2.3.1 | Closure of an air-filled door seal |
| Section 3.1.1 | Symmetric results transfer for a static tire analysis |
| Section 3.1.2 | Steady-state rolling analysis of a tire |
| Section 3.1.3 | Subspace-based steady-state dynamic tire analysis |
| Section 3.1.4 | Steady-state dynamic analysis of a tire substructure |
| Section 3.1.5 | Coupled acoustic-structural analysis of a tire filled with air |
| Section 3.1.7 | Analysis of a solid disc with Mullins effect |
| Section 3.1.8 | Tread wear simulation using adaptive meshing in ABAQUS/Standard |
| Section 3.2.1 | Inertia relief in a pick-up truck |
| Section 3.2.2 | Substructure analysis of a pick-up truck model |
| Section 4.1.1 | Resolving overconstraints in a multi-body mechanism model |
| Section 4.1.2 | Crank mechanism |
| Section 4.1.3 | Snubber-arm mechanism |
| Section 4.1.4 | Flap mechanism |
| Section 4.1.5 | Tail-skid mechanism |
| Section 4.1.7 | Driveshaft mechanism |
| Section 4.1.8 | Geneva mechanism |
| Section 4.1.9 | Trailing edge flap mechanism |
| Section 4.1.10 | Substructure analysis of a one-piston engine model |
| Section 5.1.1 | Thermal-stress analysis of a disc brake |
| Section 5.1.2 | A sequentially coupled thermal-mechanical analysis of a disc brake with an Eulerian approach |
| Section 5.1.3 | Exhaust manifold assemblage |
| Section 5.1.4 | Coolant manifold cover gasketed joint |
| Section 5.1.5 | Radiation analysis of a plane finned surface |
| Section 6.1.1 | Eigenvalue analysis of a piezoelectric transducer |
| Section 6.1.2 | Transient dynamic nonlinear response of a piezoelectric transducer |
| Section 6.2.1 | Thermal-electrical modeling of an automotive fuse |
| Section 7.1.1 | Hydrogen diffusion in a vessel wall section |
| Section 7.1.2 | Diffusion toward an elastic crack tip |
| Section 8.1.1 | Fully and sequentially coupled acoustic-structural analysis of a muffler |
| Section 8.1.2 | Coupled acoustic-structural analysis of a speaker |
| Section 8.1.6 | Coupled acoustic-structural analysis of a pick-up truck |
| Section 8.1.7 | Long-duration response of a submerged cylinder to an underwater explosion |
| Section 9.1.1 | Plane strain consolidation |
| Section 9.1.2 | Calculation of phreatic surface in an earth dam |
| Section 9.1.3 | Axisymmetric simulation of an oil well |
| Section 9.1.4 | Analysis of a pipeline buried in soil |
| Section 10.1.1 | Jack-up foundation analyses |
| Section 10.1.2 | Riser dynamics |
| Section 11.2.1 | Design sensitivity analysis of a composite centrifuge |
| Section 11.2.2 | Design sensitivities for tire inflation, footprint, and natural frequency analysis |
| Section 11.2.3 | Design sensitivity analysis of a windshield wiper |
| Section 11.2.4 | Design sensitivity analysis of a rubber bushing |
| Section 12.1.2 | Joining data from multiple results files and converting file format: FJOIN |
| Section 12.1.3 | Calculation of principal stresses and strains and their directions: FPRIN |
| Section 12.1.4 | Creation of a perturbed mesh from original coordinate data and eigenvectors: FPERT |
| Section 12.1.5 | Output radiation viewfactors and facet areas: FRAD |
| Section 12.1.6 | Creation of a data file to facilitate the postprocessing of elbow element results: FELBOW |