Cheers!

Overview

Have you ever feel frustrated that the soda liquid line always rises higher than your expectation that it spilled all over your table? We are here to help. 'Cheers' is a automated soda pouring machine that takes a bottled soda and pour it into glassware without spilling the fizz. It utilizes 3D printing techniques for contructing the mechanical framework and Arduino to control the system. 'Cheers' tilts your soda bottle and glass to a angle towards each other to minimize the fizzing and the tilting mechanism will stop after the beer height reached your desired level and voila, Cheers!

Team Members

• Jessie Shi (Tianjiao): Chemical Engineering, System Engineering ’18
• Haixiang Ren: System Engineering ’18
• Natalie Ng: TA

Objective

Figure 1

1. Replicate the project found on youtube but replace the beer bottle with soda glass bottle and a correct size glassware. There will also be no bottle rotating mechanism. The control for tilting mechanism will be changed to a pulley rope system outlined in Figure 1.
2. Glassware can have two angles. Position 1 is perpendicular to the table (Figure 2) and position 2 is tilted by an angle to the horizont. Angle is determined through experiments that if the glassware were tilted to that angle and filled without spilling, the liquid will take up approximately 2/3 of the total volume of glassware.
3. Soda bottle should be able to have 3 positions, each is shown in Figures 2, 3 and 4 respectively. The latter two angles will be determined through experiments. Position 2 will be when the first drop of soda occurs and position 3 is when all the soda in bottle could be poured out.
4. There will be one pouring mechanisms, glassware and soda bottles should both tilt fast from position 1 (Figure 2) to position 2 (Figure 3) (reach this position at the same time). Glassware is kept at position 2 and the soda bottle is tilted very slowly from position 2 to position 3 to pour the soda slowly into the glassware. When the liquid in glassware reached approximately 3 cm to its tip, it will tilt back slowly to position 1 while soda is still pouring. Glassware reaching position 1 and soda bottle reaching position 3 should be at the same time. This is when the pouring mechanism ends, and then the soda bottle will return fast to position 1.
5. Weight sensor will be used to estimate the amount of liquid in glassware and thus controls the tilting mechanism.
6. Start of the program is through pressing a push button.
7. Wood protection cover will be used to on top of the Arduino, motors and spool. Four pulley will be used as shown in Figure 1 to eliminate the chances of electric shock. The wires to connect the weight sensor to the Arduino board will be inside the support stands (Figure 1).
8. All the soda from bottle should be poured into the glassware, which would fill it 2 cm to the tip.
9. The demo will include demonstration on pouring soda using the complete assembled model.

• • • • • • • • • • • • • • we will attach new picture of the specified glassware and kind of soda bottle by friday and new figure 1, figure 2 (with estimated positions of 2s for bottle and glassware **************

Challenges

1. 3D printing
   • learn solidworks
   • design specific dimensions of soda bottle, glassware holder and frame (we will have to print two parts of the frame and connect them together as 3D printing can only print a height of 6 inches)
   • design two spools that could fit onto the stepper motor to control the rope length and four pulleys.
   • build models using Solidworks and 3D print them.
2. Arduino
   • Learn Arduino programming language.
   • Implementing the Arduino code with weight sensor and stepper motor.
   • Debugging code and and adjusting parameters to control the tilting mechanism.
3. Hardware
   • Stepper motor should keep control system stable during tilting mechanism and not going too fast/slow
   • Design a circuit that connects the step motor, push button, laser sensor onto Arduino.
   • Optimal height of laser pointer should be determined as the glassware is tilted.
   • Determine the rpm value on step motor as the spool pulls the fishing line, which controls the tilt angle.
   • The soda bottle should be able to tilt an angle more than 90 degrees (position 3) from its original position.
4. Safety
   • Electricity hazard when circuit interacts with liquid
   • Rope might break

Budget

1. Nema 17 Stepper Motor x 2: $24.98
2. Load Cell Amplifier HX-711: $9.95+ ???shippiing
3. Load Cell, straight bar 10kg: $6.95
4. Wall Adapter Power Supply: $5.69
5. Epoxy Glue: $7.28
6. Tack Switch Push Button: $1.99 (+$2.69 shipping)
7. Extension Cord: $7.99
8. Resistor Kit: $9.89
9. Screw and Nut: $8.99
10. Coca-Cola Mexican Glass Bottle, 355 mL:$5.98 (purchase in store)
11. Arduino: provided
12. 3D printing: provided
13. Power Pro Fishing Braided line – 50 lbs limit: owned
14. Magnet Screw Driver tool kit - owned
15. Wooden base and wooden protection cover - provided
16. buy something for water

Total: $ 78.82 (recalculate required!!!!!!!!!!!!!!!!!!!)

Gantt Chart