A.2 Keyword support from the input file reader
To see keywords beginning with a particular letter of the alphabet, click that letter in the table below.
*ADAPTIVE MESHCONTROLS, ELSET, FREQUENCY, INITIAL MESH SWEEPS, MESH SWEEPS, OP
*ADAPTIVE MESH CONTROLSADVECTION, CURVATURE REFINEMENT, GEOMETRIC ENHANCEMENT, INITIAL FEATURE ANGLE, MESH CONSTRAINT ANGLE, MESHING PREDICTOR, MOMENTUM ADVECTION, NAME, RESET, SMOOTHING OBJECTIVE, TRANSITION FEATURE ANGLE
*AMPLITUDEBEGIN, DEFINITION (All values except: BUBBLE), FIXED INTERVAL, NAME, SMOOTH, TIME
*BEAM GENERAL SECTIONDENSITY, ELSET, DEPENDENCIES, POISSON, SECTION (All values except: NONLINEAR GENERALMESHED), ZERO
*BEAM SECTIONDENSITY, ELSET, MATERIAL, POISSON, SECTION (All values except: ELBOW, MESHED), TEMPERATURE, ZERO
*BOUNDARYAMPLITUDE, FIXED, INC, OP, SUBMODEL, STEP, TYPE
*CFILMAMPLITUDE, FILM AMPLITUDE, OP, REGION TYPE, USER
*CONNECTOR DAMPINGCOMPONENT, COUPLED, DEPENDENCIES, ELSET, INDEPENDENT COMPONENTS, NONLINEAR
*CONNECTOR ELASTICITYCOMPONENT, COUPLED, DEPENDENCIES, ELSET, INDEPENDENT COMPONENTS, MOTION DEPENDENCIES, NONLINEAR, RIGID
*CONNECTOR FRICTIONCOMPONENT, DEPENDENCIES, INDEPENDENT COMPONENTS, PREDEFINED, STICK STIFFNESS
*CONTACT CONTROLSABSOLUTE PENETRATION TOLERANCE, APPROACH, AUTOMATIC TOLERANCES, CPSET, FASTLOCALTRK, FRICTION ONSET, GLOBTRKINC, MAXCHP, MASTER, PERRMX, RELATIVE PENETRATION TOLERANCE, RESET, SCALE PENALTY, SLIDE DISTANCE, SLAVE, STABILIZE, STIFFNESS SCALE FACTOR, TANGENT FRACTION, WARP CHECK PERIOD, WARP CUT OFF (This option is supported for ABAQUS/Explicit only; only one definition per step is supported.)
*CONTACT PAIRINTERACTION, ADJUST, SMALL SLIDING, TIED, CPSET, OP, HCRIT, MECHANICAL CONSTRAINT, NO THICKNESS, TYPE, WEIGHT
*CONTOUR INTEGRALCONTOURS, CRACK NAME, CRACK TIP NODES, DIRECTION, FREQUENCY, NORMAL, OUTPUT, SYMM, TYPE
*COUPLINGCONSTRAINT NAME, REF NODE, SURFACE, INFLUENCE RADIUS, ORIENTATION
*DLOADAMPLITUDE, CONSTANT RESULTANT, FOLLOWER, OP, ORIENTATION
*DSLOADAMPLITUDE, CONSTANT RESULTANT, FOLLOWER, OP, ORIENTATION
*DYNAMICADIABATIC, ALPHA, HAFTOL, DIRECT USER CONTROL, ELEMENT BY ELEMENT, EXPLICIT, FIXED TIME INCREMENTATION, INITIAL, NOHAF, SCALE FACTOR, SUBSPACE, VECTORS
*ELASTICDEPENDENCIES, MODULI, TYPE (All values except: SHORT FIBER)
*ELSETELSET, GENERATE, INSTANCE, INTERNAL, TYPE
*EMBEDDED ELEMENTABSOLUTE EXTERIOR TOLERANCE, EXTERIOR TOLERANCE, HOST ELSET, ROUNDOFF TOLERANCE
*EQUATION: (No parameters. This option is supported if the data lines contain only node sets; the use of node labels for this option is not yet supported in ABAQUS/CAE. In addition, the second node set (the fourth data item) can contain only a single node.)
*EXPANSIONDEPENDENCIES, PORE FLUID, TYPE (All values except: SHORT FIBER), USER, ZERO
*FILMAMPLITUDE, FILM AMPLITUDE, OP
*FREQUENCYACOUSTIC COUPLING, BIAS, EIGENSOLVER, NORMALIZATION, NUMBER INTERVAL, PROPERTY EVALUATION, USER BOUNDARIES
*FRICTIONANISOTROPIC, DEPENDENCIES, DEPVAR, ELASTIC SLIP, EXPONENTIAL DECAY, LAGRANGE, PROPERTIES, ROUGH, SHEAR TRACTION SLOPE, SLIP TOLERANCE, TAUMAX, TEST DATA, USER
*GASKET SECTIONBEHAVIOR, ELSET, MATERIAL, ORIENTATION, STABILIZATION STIFFNESS
*HYPERELASTICARRUDA-BOYCE, BETA, MARLOW, MOONEY-RIVLIN, MODULI, N, NEO HOOKE, OGDEN, POISSON, POLYNOMIAL, PROPERTIES, REDUCED POLYNOMIAL, TEST DATA INPUT, TYPE, USER, VAN DER WAALS, YEOH
*INITIAL CONDITIONSFILE, INC, MIDSIDE, STEP, TYPE (All values except: ACOUSTIC STATIC PRESSURE, CONCENTRATION, CONTACT, FIELD, FLUID PRESSURE, HARDENING, MASS FLOW RATE, NONAXI, OLD MESH, PORE PRESSURE, PRESSURE STRESS, RATIO, RELATIVE DENSITY, SATURATION, SOLUTION, SPECIFIC ENERGY, SPUD EMBEDMENT, SPUD PRELOAD, STRESS, SPECIFIC ENERGY)
*MASSELSET, ALPHA, COMPOSITE
*MEMBRANE SECTIONCONTROLS, ELSET, MATERIAL, ORIENTATION, POISSON (All values except: MATERIAL)
*NCOPYCHANGE NUMBER, OLD SET, NEW SET, POLE, REFLECT, SHIFT, MULTIPLE
*NFILLBIAS, NSET, SINGULAR, TWO STEP
*NSETGENERATE, INSTANCE, INTERNAL, NSET, TYPE
*ORIENTATIONDEFINITION (All values except: OFFSET TO NODES), SYSTEM, NAME
*ORNLA, H, MATERIAL, RESET
*OUTPUTFIELD, FILTER, FREQUENCY, HISTORY, MODE LIST, NUMBER INTERVAL, OP, TIME INTERVAL, TIME MARKS, VARIABLE
*PLASTICDATA TYPE, DEPENDENCIES, HARDENING, PROPERTIES, RATE
*PRINTALLKE, CONTACT, CRITICAL ELEMENT, DMASS, ETOTAL, FREQUENCY, PLASTICITY, RESIDUAL, SOLVE
*RESTARTWRITE, FREQUENCY, OVERLAY, NUMBER INTERVAL, TIME MARKS
*RIGID BODYANALYTICAL SURFACE, ELSET, ISOTHERMAL, REF NODE, POSITION, TIE NSET, PIN NSET
*SECTION CONTROLSHOURGLASS, KINEMATIC SPLIT, NAME, SECOND ORDER ACCURACY, WEIGHT FACTOR
*SFILMAMPLITUDE, FILM AMPLITUDE, OP
*SHELL GENERAL SECTIONCOMPOSITE, CONTROLS, ELSET, MATERIAL, ORIENTATION, POISSON, STACK DIRECTION, THICKNESS MODULUS
*SHELL SECTIONCOMPOSITE, CONTROLS, ELSET, MATERIAL, ORIENTATION, POISSON (All values except: ELASTIC, MATERIAL), SECTION INTEGRATION, STACK DIRECTION, TEMPERATURE, THICKNESS MODULUS
*SOILSCETOL, CONSOLIDATION, END, FACTOR, NO CREEP, UTOL, STABILIZE
*STATICADIABATIC, DIRECT, FACTOR, FULLY PLASTIC, LONG TERM, RIKS, STABILIZE
*STEADY STATE DYNAMICSDIRECT, SUBSPACE PROJECTION, FREQUENCY SCALE, INTERVAL, REAL ONLY, DAMPING CHANGE, STIFFNESS CHANGE
*STEPAMPLITUDE, EXTRAPOLATION, INC, NLGEOM, PERTURBATION, SOLVER, UNSYMM, NAME
*SURFACECOMBINE, CROP, FILLET RADIUS, GENERATE, INTERNAL, NAME, REF NODE, TYPE (All values except: USER)
*TEMPERATUREABSOLUTE EXTERIOR TOLERANCE, AMPLITUDE, BINC, BSTEP, EINC, ESTEP, EXTERIOR TOLERANCE, FILE, INPUT, INTERPOLATE, MIDSIDE, OP, USER
*TIEADJUST, NAME, NO ROTATION, NO THICKNESS, POSITION TOLERANCE, CONSTRAINT RATIO, TYPE
*VARIABLE MASS SCALINGCROSS SECTION NODES, DIRECTION, DT, ELSET, EXTRUDED LENGTH, FEED RATE, FREQUENCY, TYPE, NUMBER INTERVAL
*VISCOCETOL, EXPLICIT, FACTOR, STABILIZE, CREEP
