Products: ABAQUS/Standard ABAQUS/CAE
The hysteresis material model:
defines strain-rate-dependent, hysteretic behavior of materials that undergo comparable elastic and inelastic strains;
provides inelastic response only for shear distortional behavior—the response to volumetric deformations is purely elastic;
can be used only in conjunction with “Hyperelastic behavior,” Section 10.5.1, to define the elastic response of the material—the elasticity can be defined either in terms of the instantaneous moduli or the long-term moduli;
is active during a static analysis (“Static stress analysis,” Section 6.2.2), a quasi-static analysis (“Quasi-static analysis,” Section 6.2.5), or a transient dynamic analysis using direct integration (“Implicit dynamic analysis using direct integration,” Section 6.3.2)—it cannot be used in fully coupled temperature-displacement analysis (“Fully coupled thermal-stress analysis,” Section 6.5.4) or steady-state transport analysis (“Steady-state transport analysis,” Section 6.4.1);
cannot be used to model temperature-dependent creep material properties—however, the elastic material properties can be temperature dependent;
can be used only in large-strain problems; and
uses unsymmetric matrix storage and solution by default.
Nonlinear strain-rate dependence of elastomers is modeled by decomposing the mechanical response into that of an equilibrium network (A) corresponding to the state that is approached in long-time stress relaxation tests and that of a time-dependent network (B) that captures the nonlinear rate-dependent deviation from the equilibrium state. The total stress is assumed to be the sum of the stresses in the two networks. The deformation gradient, 
, is assumed to act on both networks and is decomposed into elastic and inelastic parts in network B according to the multiplicative decomposition 
The nonlinear rate-dependent material model is capable of reproducing the hysteretic behavior of elastomers subjected to repeated cyclic loading. It does not model “Mullins effect”—the initial softening of an elastomer when it is first subjected to a load.
The material model is defined completely by:
a hyperelastic material model that characterizes the elastic response of the model;
a stress scaling factor, 
, that defines the ratio of the stress carried by network B to the stress carried by network A under instantaneous loading; i.e., identical elastic stretching in both networks;
a positive exponent, 
, generally greater than 1, characterizing the effective stress dependence of the effective creep strain rate in network B;
an exponent, 
, restricted to lie in 
, characterizing the creep strain dependence of the effective creep strain rate in network B; and
a nonnegative constant, 
, in the expression for the effective creep strain rate—this constant also maintains dimensional consistency in the equation.
is the effective creep strain rate in network B, 
is the nominal creep strain in network B, and 
is the effective stress in network B. The chain stretch in network B, 
, is defined as
. The effective stress in network B is defined as 
, where 
is the deviatoric Cauchy stress tensor.The elasticity of the model is defined by a hyperelastic material model. You input the stress scaling factor and the creep parameters for network B directly when you define the hysteresis material model. Typical values of the material parameters for a common elastomer are 
, 
(sec)–1(MPa)–m, 
, and 
(Bergstrom and Boyce, 1998).
| Input File Usage: | Use both of the following options within the same material data block: |
*HYSTERESIS *HYPERELASTIC |
| ABAQUS/CAE Usage: | Property module: material editor: Mechanical |
The use of the hysteresis material model is restricted to elements that can be used with hyperelastic materials (“Hyperelastic behavior,” Section 10.5.1). In addition, this model cannot be used with elements based on the plane stress assumption (shell, membrane, and continuum plane stress elements). Hybrid elements can be used with this model only when the accompanying hyperelasticity definition is completely incompressible. When this model is used with reduced-integration elements, the instantaneous elastic moduli are used to calculate the default hourglass stiffness.
In addition to the standard output identifiers available in ABAQUS/Standard (“ABAQUS/Standard output variable identifiers,” Section 4.2.1), the following variables have special meaning if hysteretic behavior is defined:
EE | Elastic strain corresponding to the stress state at time |
CE | Equivalent creep strain defined as the difference between the total strain and the elastic strain. |
Elasticity
and the instantaneous elastic material properties.