Difference between revisions of "Data Acquisition Basics"
From ESE497 Wiki
Jump to navigationJump to search (Created page with '** LabVIEW Tutorial *** Code up examples in LabVIEW for slides 11, 14, 27, 31, 36, 38, 41. Put each one in a separate VI and demo to me or T/A.…') |
|||
| (13 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | * [[media:LabVIEW_Introduction.pdf|LabVIEW Tutorial]] | |
| − | + | ** Code up examples in LabVIEW for slides 11, 14, 27, 31, 36, 38, 41. Put each one in a separate VI and demo to me or T/A. | |
| − | + | ** Configure LabVIEW options as shown in slides 15-17 | |
| − | ** | + | ** [http://www.ni.com/academic/students/learnlabview NI LabVIEW 101] |
| − | + | * Homework 3 - Watch LabVIEW 101 Tutorials | |
| − | + | * Assign Project1 - Simulation | |
| − | + | * Homework 4 | |
| − | + | ** A: Finish ComputeAngle.vi (in Project1 -> RoboticSensing.zip -> micSourceLocator.lvproj -> My Computer -> ComputeAngle.vi) | |
| − | + | ** B: Finish ComputeIntersection.vi | |
| − | + | * Additional Resources | |
| − | + | ** Conditionally append values to an array in a loop | |
| − | + | ** [http://cnx.org/content/m12220/latest/ How to Create an Array on the Front Panel] | |
| − | + | * [[media:Data_Acquisition_Basics.pdf|Data Acquisition Basics]] | |
| − | + | ** Homework 5 - Finish exercise | |
| + | ** Homework 6 - Connect wires from A00 and AO1 to AI0+ and AI1+ (remove wire from Banana A to AI0+). Make sure that the Prototyping Power is on. Modify your vi from Homework 5 to collect samples from both AI0 and AI1. Then open [[media:DelayedChirp2DAC.zip|DelayedChirp2DAC.vi]] and run this vi. You shouldn't modifiy DelayedChirp2Dac.vi. Run your modified Homework 5 vi and zoom in in the time and frequency domain to examine the waveforms in detail. Describe in detail what you see. Measure the difference in time between both channels. Hint: Start and stop your Data Acquisition vi until the entire signal is in the middle of the buffer. | ||
Latest revision as of 20:15, 4 September 2015
- LabVIEW Tutorial
- Code up examples in LabVIEW for slides 11, 14, 27, 31, 36, 38, 41. Put each one in a separate VI and demo to me or T/A.
- Configure LabVIEW options as shown in slides 15-17
- NI LabVIEW 101
- Homework 3 - Watch LabVIEW 101 Tutorials
- Assign Project1 - Simulation
- Homework 4
- A: Finish ComputeAngle.vi (in Project1 -> RoboticSensing.zip -> micSourceLocator.lvproj -> My Computer -> ComputeAngle.vi)
- B: Finish ComputeIntersection.vi
- Additional Resources
- Conditionally append values to an array in a loop
- How to Create an Array on the Front Panel
- Data Acquisition Basics
- Homework 5 - Finish exercise
- Homework 6 - Connect wires from A00 and AO1 to AI0+ and AI1+ (remove wire from Banana A to AI0+). Make sure that the Prototyping Power is on. Modify your vi from Homework 5 to collect samples from both AI0 and AI1. Then open DelayedChirp2DAC.vi and run this vi. You shouldn't modifiy DelayedChirp2Dac.vi. Run your modified Homework 5 vi and zoom in in the time and frequency domain to examine the waveforms in detail. Describe in detail what you see. Measure the difference in time between both channels. Hint: Start and stop your Data Acquisition vi until the entire signal is in the middle of the buffer.
