Difference between revisions of "Data Acquisition Basics"
From ESE497 Wiki
Jump to navigationJump to search (Created page with '** LabVIEW Tutorial *** Code up examples in LabVIEW for slides 11, 14, 27, 31, 36, 38, 41. Put each one in a separate VI and demo to me or T/A.…') |
|||
| Line 1: | Line 1: | ||
| − | + | * [[media:LabVIEW_Introduction.pdf|LabVIEW Tutorial]] | |
| − | + | ** Code up examples in LabVIEW for slides 11, 14, 27, 31, 36, 38, 41. Put each one in a separate VI and demo to me or T/A. | |
| − | + | ** Configure LabVIEW options as shown in slides 15-17 | |
| − | + | ** Exercises 1,2,3 | |
| − | + | * Homework 3 - Finish Exercises | |
| − | + | * Assign Project1 - Simulation | |
| − | + | * Homework 4 - Finish ComputeAngle.vi (in Project1 -> RoboticSensing.zip -> micSourceLocator.lvproj -> My Computer -> ComputeAngle.vi) and ComputeIntersection.vi | |
| − | + | * Additional Resources | |
| − | + | ** Conditionally append values to an array in a loop | |
| − | + | ** [http://cnx.org/content/m12220/latest/ How to Create and Array on the Front Panel] | |
| − | + | ** [http://zone.ni.com/devzone/cda/tut/p/id/7521 LabVIEW tutorial], [http://www.ni.com/academic/students/learnlabview LabVIEW 101] | |
| − | + | * [[media:Data_Acquisition_Basics.pdf|Data Acquisition Basics]] | |
| − | + | ** Homework 5 - Finish exercise | |
| − | + | ** Homework 6 - Connect wires from A00 and AO1 to AI0+ and AI1+ (remove wire from Banana A to AI0+). Make sure that the Prototyping Power is on. Modify your vi from Homework 5 to collect samples from both AI0 and AI1. Then open [[media:DelayedChirp2DAC.zip|DelayedChirp2DAC.vi]] and run this vi. You shouldn't modifiy DelayedChirp2Dac.vi. Run your modified Homework 5 vi and zoom in in the time and frequency domain to examine the waveforms in detail. Describe in detail what you see. Measure the difference in time between both channels. Hint: Start and stop your Data Acquisition vi until the entire signal is in the middle of the buffer. | |
Revision as of 16:28, 29 May 2012
- LabVIEW Tutorial
- Code up examples in LabVIEW for slides 11, 14, 27, 31, 36, 38, 41. Put each one in a separate VI and demo to me or T/A.
- Configure LabVIEW options as shown in slides 15-17
- Exercises 1,2,3
- Homework 3 - Finish Exercises
- Assign Project1 - Simulation
- Homework 4 - Finish ComputeAngle.vi (in Project1 -> RoboticSensing.zip -> micSourceLocator.lvproj -> My Computer -> ComputeAngle.vi) and ComputeIntersection.vi
- Additional Resources
- Conditionally append values to an array in a loop
- How to Create and Array on the Front Panel
- LabVIEW tutorial, LabVIEW 101
- Data Acquisition Basics
- Homework 5 - Finish exercise
- Homework 6 - Connect wires from A00 and AO1 to AI0+ and AI1+ (remove wire from Banana A to AI0+). Make sure that the Prototyping Power is on. Modify your vi from Homework 5 to collect samples from both AI0 and AI1. Then open DelayedChirp2DAC.vi and run this vi. You shouldn't modifiy DelayedChirp2Dac.vi. Run your modified Homework 5 vi and zoom in in the time and frequency domain to examine the waveforms in detail. Describe in detail what you see. Measure the difference in time between both channels. Hint: Start and stop your Data Acquisition vi until the entire signal is in the middle of the buffer.
