Maze Craze Weekly Log

Week of 1/23/17

• We formulated our team and brainstormed ideas for our project. Then, we decided on our maze game idea and began writing a simple project proposal.

Week of 1/30/17

• We wrote a starting proposal for Maze Craze including a Gantt chart and budget. After meeting with our TA Natalie, we solidified our proposal and overall project idea.
• Once the project proposal is approved, we will design our game board and layout for the maze so that we can order parts to begin construction.
• In addition, we seem to have a clear schedule of when we will be able to work on the project individually and together.

Week of 2/6/17

• We started designing a layout for our game board with possible dimensions that may be subject to change depending on the parts we ultimately use.
• Revisions were made to the project proposal by editing the project description, budget, objectives and challenges. The budget still needs a few prices to be confirmed as we finalize our decisions on a few parts such as the amount of wood we will need which will depend on the final dimensions we choose for our board.

Week of 2/13/17

• This week we had serious problems with our budget. We had to overhaul almost everything on it in order to stay under $150. All of the items below have been added to our budget:

1. We found a new website to order the LED RGB strips.
2. We reduced our order of hall effect sensors to 27 as we only require 25 but want to have a couple extra.
3. We found cheaper spray paint for $3.87 rather than $8.00.
4. We are now ordering a 5V 10 Amp Power Supply rather than using battery packs to power the Arduino.
5. We found cheaper screws that will still suffice to keep our box together.
6. We also found out that we needed 10K Resistors in order to use the hall effect sensors properly.
7. Instead of using LEDs for the number displays we will be using cheaper analog number displays.
8. We found a cheaper breadboard that should achieve our needs.
9. We also need a female DC power adapter to connect the power supply to the Arduino.
10. We will also be upgrading our Arduino to a Mega Arduino.

Week of 2/20/17

• This week we ordered:

1. All the Sparkfun items (Lights, Hall Effect Sensors, Resistors, and Switch)
2. Breadboards

• We visited Home Depot to get our wood, screws, paint, etc.
• Jason mocked up a basic version of the game in Java. The two versions we mocked up were:

1. A version that generates a random maze every move
2. A version that cycles between two mazes with every move

• Jason also tested how probability that each wall it lit affects the solvability of a maze by altering the probability and playing through several mazes at different probabilities.
• We discussed the "maze generating" algorithm and how each maze will be created. We mocked this up in We decided:

1. Not every maze has to be solvable
2. The mazes cannot be generated completely randomly because they will generally be unsolvable
3. Every time a game starts, a completely new set of mazes will be generated
4. A possible way of controlling difficulty is generate random numbers for each wall and altering the likelihood of a wall to be green (~60% green is a fairly easy game, while a 40% is much more difficult and likely impossible)
5. The two walls bordering the entrance and the two bordering the exit must always stay on

• Liz mocked up the basic wall/sensor code on an Arduino. It:

1. Models a set of walls (with LEDs)
2. Responds to a user's button presses by lighting a different set of walls (modeled by LEDs)
3. Does not respond if a user doesn't move but just "sets their piece back down" (modeled by buttons)
4. Waits for a player to set their piece in the "start" position to begin the game

Week of 2/27/17

• This week, the following parts arrived:

1. The 1k and 10k resistors
2. The 3 solderless breadboards
3. The 3 strips of LED lights
4. The 27 Hall Effect Sensors
5. The on/off switch

• Liz got a Hall Effect sensor wired up to an Arduino Uno properly and is getting proper readings with test magnets

1. We figured out our Hall Effect sensors are "latching", meaning that they return a '0' until a magnet is sensed, then a '1' until the magnet is sensed again. This changes they way we will go about coding how a player's game piece is registered, but we have a good idea about how to handle this involving an array of "last states" and "current states" of each Hall Effect sensor
2. Our 10k resistors worked with the Hall Effect sensors

• Jason sketched up a 1:2 scale drawing of the top of the game board. This is pictured below.

• We began looking into the coding of the addressable LED strips

1. We found a library that other users of the same LED strips say works well. This code is quite over our head, so we are planning to seek help from Natalie, our TA, with the controls of the lights. This library is linked: Adafruit NeoPixel Library
2. We discovered that our RGB lights do not have adhesive backing and are also more expensive than the other RGB strips. We are considering returning the current LEDs and ordering the LEDs with the adhesive backing.

• We were having problems wiring up the LED strips. We hope to get help from Natalie to figure how to wire the LEDs up.
• We began strategizing MegaArduino pin distribution.

1. 25 digital pins will be used for Hall Effect sensing
2. 8 pins (unclear whether analog or digital as of yet) will be used to control each strand of RGB LED strips
3. 1 pin will be used for the on/off switch
4. Up to 20 pins could be used for number displays (this is in the air at this point, as we don't know whether we'll have time or funding for this feature)

• We updated our "Challenges" portion of our project wiki to reflect the currently projected issues.

Week of 3/6/17

• The hall effect sensors we ordered are latching and our game requires that are non-latching. We found a program online that helped us program the sensor to act as a digital reed switch. This means that the sensors will detect when a magnet is near and act like a switch being toggled on. When the magnet is out of detection range the hall effect sensor will no longer provide an output and be switched off.
• We started learning how to 3D print and printed a sample piece from Thingiverse.
• Liz got the LED light strips to turn on using Adafruit’s NeoPixel library test code.
• Jason created a design for a casing to go around our hall effect sensors to attach them to the top of our box.

Week of 3/13/17 (Spring Break)

• Jason worked on the maze generation algorithms. He:

1. Realized that a player could only reach certain squares at certain times because of the nature of the game. (IE, a certain square may be accessible on maze 2 due to the switching of the mazes). This may aid us in testing if mazes are solvable.
2. Designed a storage system for the maze data. This is a 2-D array holding 4-bit binary characters that represents each wall. These 4-bit numbers will be processed with a bit mask.

• Liz worked on getting the lights and Hall effect sensors working. She:

A single strand of LEDs responding to a magnet's presence. Please click to watch.

1. Designed a Lights Protocol that converts from programmer-friendly addressing (IE vertical wall at 0, 1 is set to GREEN) to RGB values and turns the lights in that specific wall on.
2. Wired up a few different light strands and got them to respond and change color to a user's game piece.
3. Practiced designing colors and implementing them.
4. Worked on her soldering skills in preparation for the coming weeks.

• Together, Jason and Liz worked on brainstorming for the future of the game board. We discussed:

1. New game ideas (A TRON-inspired game where you race against a computer to a finish, a "whack-a-mole for adults" where you have to hunt and find the correct color and place your piece before a certain time, a basic maze, and tic tac toe).

Week of 3/20/17

• We drilled all 180 holes for the lights in the board.
• We spray-painted the top panel of the board flat black. See picture below.

= Week of 3/27/17

• We attached the lights to the top face of the board using tape. See picture below.